Search results

I think youll have to pop the plastic centre console off (4 screws) and take out the 4 screws holding heater controlpanel in, then you can twist the panel and get behind to the bulb holders. They are twist fit, but its difficult to get fingers in. I fitted a blue T10 LED in mine (circled in red...

Anyone got a faulty or cheap boot latch (with cable opening arm) they dont want? Im thinking i could drill the rivet out and swap the arms over. Would need a hole drilling in body for release arm too, but only half an hours job (prob end up being a whole afternoon??). I just need a donor release...

Please refer to photos below. I recently bought a new boot latch with the light switch on it. Ive got it all wired up and working, then i realised the handle release by drivers seat doesnt work with the switched latch. There is no release trigger which the cable trips to release the catch, arrow...

For boot light the wiring is stright forward, but you need a tailgate latch with a switch, or you can put a switch in the boot somewhere. I was using a stick on light from poundland which i stuck under parcel shelf. But i just bought a boot latch with switch. To wire it use the latch swith to...

What i did to fix door wa make a couple of plastic spacers to go under the bottom hinge only. Cut some plastic which was about 1.2mm thick and drilled an 8.5mm hole in it. I loosened top hinge bolts a little and bottom hinge bolts a lot, then used a jack with towel on top to push the door up...

Good description of this task thank you. I just replaced OS wing on my car which had rotted through right aroung the wheel arch. The NS wing has no rust at all. Another tip is to remove 2 bolts holding the bumper on in front of the wing you are removing. You can then pull it out and drop the...

Has anyone tried these bushings on 3 door k11 (mines 2002) ? Or does anyone know the bushing measurements? I took a scrshot from ali express ENGLISH PAGE...

I think theyre meant to go on top of shelf to stop it jumping up. Not a great fit though as im having to slam the boot quite hard to get it to latch now. Ill try putting some pipe insulation on the shelf to hold it and see how that works.

Yes i looked at it yesterday, one side will go above parcel shelf to hold it down when on bumpy roads. But the other side is getting trapped between door and shelf, i will probably remove it. Will post photos later.

Ah, ok thank you FinnishCoffee and Twincam-Alex. Ive never seen this before on other cars.ill investigate further now i know why they are there??. My parcel shelf is from pre-facelift car, my car is a facelift so its not the exact parcel shelf but fits pretty well apart from the cut out around...

Rear Tailgate (Hatch Door); Help. What are these 2 rubber lugs for? They catch on the parcel shelf so I want to remove them. But just had a thought that they may be related to rear window glass. But they dont seem to be attached to anything and i cant see what use they are or why nissan put them...

Hi Earnestnine. The splitter never worked correctly, i have returned to amazon. I bought the magnetic mount with 5m cable aerial from Halfords (£9.99) and I am getting ok results with that. Its not great reception around west yorkshire and planet rock / absolute rock drop out all the time, but...

The Almera MK 2, N16 wiper stem arrived today. Here are some photos of k11 face-lift and Almera stem side by side, the Almera has white stripe intermittent speed on the end, but otherwise identical. Only a 10 minute job to swap them over. I've now got variable intermittent wipers front and...

Update: I have bought an Almera mk2 N16 wiper stem which should arrive next week, I will post the results when I put it on.

Does anyone know if the Almera stalk with variable intermittent speed will work on a face-lift k11? they are identical in all aspects but the Almera has variable intermittent wiper speed control on the end, as in bottom photo. My k11 stalk: Almera N16 stalk: All plastic parts are...

Home made parcel shelf with speakers for k11 facelift 2002. Has 2 JBL GT5-963 speakers in it. If you dont have a parcel shelf easy to make one from a piece of ply and a few bits.

WANTED parcel shelf with speakers for face-lift k11 , grey interior. I have a shelf, no speakers, but don't want to cut holes in it. Anyone want to swap? West Yorkshire. Heading down to Lincs soon so can maybe collect en route. Also im after the small speaker connector to plug into harness too...

I bought this splitter adapter (£9.99) so I can use original k11 face-lift aerial on my new DAB stereo. The DAB is working fine as far as I can tell, but only put it in yesterday. I need another adapter to fit my radio for AM/FM which is on the way from ebay ,£1.99. But all in all the splitter...

I've just bought a DAB stereo. I've put it in my face-lift k11, rather than mess about with fitting a new aerial I bought a splitter to use same areal, £9.99 on amazon. It pics up a lot of radio stations without having to change or wire a new aerial.

Does anyone know if I can screw a DAB aerial into this mount? (Pics below) I've got a splitter to use DAB through original aerial, it works ok but wanting better recrption on DAB.