Seb_'s latest activity

  • Seb_
    Seb_ reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    2025-05-17 Swap Back to Standard Engine Mounts Whilst cleaning the garage I found some spare oem engine mounts and decided to swap them...
  • Seb_
    Seb_ reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    Yeah good enough compromise for a smooth comfy drive. Fitting my PTFE manifold gasket & removing the TB coolant lines made a huge...
  • Seb_
    Seb_ reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    The standard front mount has soo much slack upto 11mm that I could noticeably rock the engine back/forth & see the softer left & right...
  • Seb_
    Seb_ reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    The completely solid front upper & lower mount (on right) with firm rear mount and OEM left & right mounts was still transferring abit...
  • Seb_
    Seb_ reacted to XPS420's post in the thread Intelligent lighting with Like Like.
    Temp sensor? To turn the friendly lighting on, you need to switch ign off and flash the highbeam, i think 1 flash is 30secs, 2 flash is...
  • Seb_
    Seb_ reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    2025-04-21 Replacing Fake Cat with Genuine Cat Began removing the fake universal cat Looking at how close the cat is to the block, I...
  • Seb_
    Seb_ reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    It's been 1yr since I last checked the compression and 2yrs since checking valve clearances 👀 Insides look good from regular 6mth...
  • Seb_
    Seb_ reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    The caliper carrier has upto 2mm gap from the disc edge Whereas the caliper sits abit closer upto 1mm gap from the disc 🫣 notice...
  • Seb_
    Seb_ reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    2025-02-17 Walbro GSS250 Fuel Pump Detailed Look For a closer look at how the Walbro 255LPH internal gear type pump works and it's...
  • Seb_
    Seb_ reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    2025-02-15 Replace Walbro GSS250 255lph Fuel Pump With approx 75% fuel level I removed the fuel pump assembly out of the tank. Not a...
  • Seb_
    Seb_ reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    Didn't have much energy today but I managed to crimp the new relay wires together Reassembled the loom & dash Couldn't be bothered...
  • Seb_
    Seb_ reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    Trying to reach that small plug behind the fuse box was difficult, so there's no option but to remove the dashboard for better access 🙈...
  • Seb_
    Seb_ reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    2025-02-11 Test Fuel Pump Voltage Drop In preparation for replacing the Walbro fuel pump, I figure it's best to first check if the pump...
  • Seb_
    Seb_ reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    2025-02-03 Solid Steel Steering Rack Mount The old 3D printed solid plastic rack bushing was once again worn loose allowing the PAS...
  • Seb_
    Seb_ reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    2025-03-18 Rebuild Garage Roof My garage roof consists of a steel mesh cage covered with a mess of clear corrugated sheets, which tends...
Show older items
Back
Top